General Product Description

Miilux Wear Resistant Steels are dimensionally accurate, ready for use as component parts and wear resistant sheets. In the production of component parts, homogeneous hardness is provided in the whole part by using edge-to-edge hardening technology.

It offers excellent design solutions in wear parts such as crushers, excavators, mining machinery wear parts, damper bodies, bulldozer blade, chute-feeders and so on. By using Miilux 500 against friction and wear, high service life is provided compared to conventional materials. Additionally, it reduces body weight and increases load capacity by allowing the use of thinner material. It shows positive cutting and welding behavior in the production.

Miilux 500; it is supplied in order thickness of 4.00-60.00 mm and hardness range of 450-560 HBW.

Heat Treatment Condition

Quenched

Quenched and Tempered

*It is subject to negotiation.

Sales and Marketing

Our Sales and Marketing team will assist you with your order requests and pre-sales services.

E-mail: satis@miilux.com.tr

Customer Technical Services

Our Customer Technical Services team will assist you in case you have any questions regarding product features, testing and usage areas.

E-mail: mth@miilux.com.tr

Dimensions and Delivery Conditions

Miilux products are available in a thickness range of 4.00-60.00 mm, with a maximum width of 2500 mm and a maximum length of 8000 mm. Other sizes are subject to agreement.

Miilux products are also available as ready-to-install component parts upon the customer request.

Ultrasonic Testing

It can be conducted in accordance with EN ISO 10160.

For application class, contact Miilux Sales Team at the order stage.

Narrowed Miilux Thickness Tolerances

Sheet Thickness (mm) Tolerances (mm)
4 – 8 - 0,35 + 0,35*
6 – 7,99 - 0,40 + 0,80**
8 – 14,99 - 0,50 + 0,90**
15 – 24,99 - 0,60 + 1,00**
25 - 50 - 0,60 + 1,30**
50,01 - 79,99 - 0,60 + 1,70**
80 - 150 - 0,60 + 2,10**

Other thicknesses are accepted subject to negotiation.

* Sheet from Coil (Without the Edge-Cut)

** Sheet (With the Edge-Cut)

Maximum Chemical Composition Compound (%) Ladle Analysis

Product Quality Thickness (mm) C Si Mn P S Cr Ni Mo B
Miilux 500
4,00≤-≤60,00
0,30
0,70
1,70
0,025
0,01
1,50
3,00
0,70
0,005

Typical Mechanical Features and Carbon Equivalent

Product Quality Thickness (mm) *Yield Strength (Rp) 0,2 N/mm²
*Tensile Strength (Rm) N/mm²
*Elongation (A5%)
Darbe Charpy-
V -40°C Joule
(Min.)
Hardness Ranges (HBW)
**CEV
Miilux 500
4,00≤-≤60,00 mm 1250 1550 8 17 450-560 0,70

*They are the typical values.

**CEV= C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15

Brinell hardness test is applied on every armour steel in accordance with EN ISO 6506-1 principles. If the thickness of the hardness measurement area is thinner than 4.75 mm, the 5/750 HBW measurement method is used. For other thicknesses, the 10/3000 HBW method is used.

Hardness tests are performed at a depth of 0.50 – 1.00 mm from the steel surface, on the machined surface.

Charpy V-Notch Impact Test is applied in perpendicular and parallel directions to the rolling direction in all castings and thickness* in accordance with EN ISO 148-1 principles. For products thinner than 11.00 mm nominal thickness, sub-size samples are used. The determined minimum impact value is then proportional to the test specimen’s cross-sectional area. (*in order thickness of 6.00 mm and thicker armour steel)

Order-specific test requests should be discussed with Miilux Sales team at the order stage.

Processing

Miilux products can be machined using high speed tool steels (HSS) with the appropriate combination of machining tool speed and feed rate, resulting in a satisfactory service life.

Cold Forming

Sharp transition angles should be avoided as much as possible when cold forming the Miilux products. In addition, the importance of the condition of the equipment used in the operations, the operation plan and good workshop practices should be taken into the consideration. The Cold Forming limits table is given below.

Product Sheet Thickness (mm) Air bending < 90° Press radius / Plate thickness (r/t) (Bend direction in rolling direction) Air bending - Die Opening / Sheet thickness (W/t)
Transversal Longitudinally  Transversal Longitudinally 
Miilux® 500
4-20
6,0
8,0
15,0
19,0
Bending should be performed with a single press | Slow press speed is recommended | Bearings should be roller type (It is indicated in the drawing.)